The best way to Care for Cleaning Equipment
As a cleaning company owner, how many times can you find filthy mop pails, dirty equipment, vacuum cleaners that haven't been emptied, and spray bottles that spray correctly and walk right into a janitor closet? Have you or your supervisors taken the time to train your workers on the best way to properly care for your equipment? Utilize this checklist to help keep your supplies and equipment in top working condition.
Wipe bottles as essential to prevent buildup and deposits
When wanted replace label
Occasionally take cause apart and clean to avoid clogging
Wipe down in and out as needed
Rags
Do not leave lying around - they are a safety and disorder danger. Keep in a bag for dirty rags
Dust Pans
Disinfect and wipe front edge as needed
Brushes
Rinse in clear, cold water, shake out excess. If brush is dirty, wash it out and rinse with clear water. Let dry with bristles.
Storage - hang brush - usually do not put the brush weight on the bristles.
Sweepers
Do not use when wet, don't stand on its straws. Do not use broom for scrubbing. So it's going to wear evenly rotate frequently.
Putty Knife
After each days use, wipe knife to eliminate debris and moisture.
Store in clean, dry location.
Border needed to keep it sharp
Measuring Cups
Rinse with water immediately.
Dust Mops
Don't use dry mops to pick up liquids. Do not use dust mops on floors that are greasy.
Remove loose soil frequently, using a vacuum cleaner if possible shake into big waste receptacle.
Never store a mop on the floor. Hang air can circulate.
Wet Mops
Soak for many minutes to remove sizing, before employing a mop that is new and toughen the fibers.
Rinse after use.
If it's twisted or squeezed too challenging it might be ruined since the actions will bust the fibers.
Cut off loose or uneven strands.
Never store on the floor or in the mop bucket.
Floor Finish Mops
After using, wash out all floor finish or wax with water that is clean.
Wring out as much water as you possibly can, shake to fluff strands.
Never use detergent or soap on a mop meant for flooring finish.
Put mop after use in a clean plastic bag.
Pails & Wringers
Do not use force on a wringer lever - use only enough hand pressure on the lever to wring out the mop.
Remove that becomes tangled in the wringer.
Wash and scrub all surfaces of janatorial supplies the bucket with disinfectant. Rinse with warm water and wipe dry. Keep wringer tight and oiled.
Keep wringer in "release" position if it is not used.
Rinse blade in clean water.
Wipe dry, usually do not store with crouched or blade down.
Vertical Vacuum Cleaners
Empty tote consistently.
After emptying wipe outside of hoover.
Check for cuts in belt when needed, and change.
Magnet that is empty bar after every use.
Buffers
Wipe down whole surface after each day's use. Additionally wipe twine.
Check pad for replacing.
Blow out motor about every 2 weeks.
Once per month check screws and bolts to ensure they are tight.
Slow Speeds
Wipe entire surface down after each day's use. Also wipe cord.
Rinse tank.
Check drive unit for cracks on wear.
Faux Flooring Pads
![]()
Flooring pads may be used on either side. The pad needs to be set aside for soaking or cleaning once both sides are used.
Floor pads can be cleaned by rubbing one against the top of another. Or you can definitely work with a hand scratcher. Pads that usually do not react to this approach needs to be soaked overnight in a concentration of synthetic detergent or stripping solution. Each pad ought to be rinsed under a sharp stream of water that was hot, after soaking. Following a final rinse of cold water, the pads must be shaken and set on a level, non-rusting surface for drying. Pads will not be prepared for reuse till they are completely dry.
Hint: When pads become worn, they can be cut into small sections that can be properly used as foot or hand scratch pads.
Wet/Dry Vacs
Rinse out in, wipe in and outside after each use.
Rinse and wipe fasteners and hoses.
Carpeting Machines
Rinse out in of filters, tank, hoses and attachments.
Discharge pressure.
Wipe outside.
As a cleaning company owner, how many times can you find filthy mop pails, dirty equipment, vacuum cleaners that haven't been emptied, and spray bottles that spray correctly and walk right into a janitor closet? Have you or your supervisors taken the time to train your workers on the best way to properly care for your equipment? Utilize this checklist to help keep your supplies and equipment in top working condition.
Wipe bottles as essential to prevent buildup and deposits
When wanted replace label
Occasionally take cause apart and clean to avoid clogging
Wipe down in and out as needed
Rags
Do not leave lying around - they are a safety and disorder danger. Keep in a bag for dirty rags
Dust Pans
Disinfect and wipe front edge as needed
Brushes
Rinse in clear, cold water, shake out excess. If brush is dirty, wash it out and rinse with clear water. Let dry with bristles.
Storage - hang brush - usually do not put the brush weight on the bristles.
Sweepers
Do not use when wet, don't stand on its straws. Do not use broom for scrubbing. So it's going to wear evenly rotate frequently.
Putty Knife
After each days use, wipe knife to eliminate debris and moisture.
Store in clean, dry location.
Border needed to keep it sharp
Measuring Cups
Rinse with water immediately.
Dust Mops
Don't use dry mops to pick up liquids. Do not use dust mops on floors that are greasy.
Remove loose soil frequently, using a vacuum cleaner if possible shake into big waste receptacle.
Never store a mop on the floor. Hang air can circulate.
Wet Mops
Soak for many minutes to remove sizing, before employing a mop that is new and toughen the fibers.
Rinse after use.
If it's twisted or squeezed too challenging it might be ruined since the actions will bust the fibers.
Cut off loose or uneven strands.
Never store on the floor or in the mop bucket.
Floor Finish Mops
After using, wash out all floor finish or wax with water that is clean.
Wring out as much water as you possibly can, shake to fluff strands.
Never use detergent or soap on a mop meant for flooring finish.
Put mop after use in a clean plastic bag.
Pails & Wringers
Do not use force on a wringer lever - use only enough hand pressure on the lever to wring out the mop.
Remove that becomes tangled in the wringer.
Wash and scrub all surfaces of janatorial supplies the bucket with disinfectant. Rinse with warm water and wipe dry. Keep wringer tight and oiled.
Keep wringer in "release" position if it is not used.
Rinse blade in clean water.
Wipe dry, usually do not store with crouched or blade down.
Vertical Vacuum Cleaners
Empty tote consistently.
After emptying wipe outside of hoover.
Check for cuts in belt when needed, and change.
Magnet that is empty bar after every use.
Buffers
Wipe down whole surface after each day's use. Additionally wipe twine.
Check pad for replacing.
Blow out motor about every 2 weeks.
Once per month check screws and bolts to ensure they are tight.
Slow Speeds
Wipe entire surface down after each day's use. Also wipe cord.
Rinse tank.
Check drive unit for cracks on wear.
Faux Flooring Pads
Flooring pads may be used on either side. The pad needs to be set aside for soaking or cleaning once both sides are used.
Floor pads can be cleaned by rubbing one against the top of another. Or you can definitely work with a hand scratcher. Pads that usually do not react to this approach needs to be soaked overnight in a concentration of synthetic detergent or stripping solution. Each pad ought to be rinsed under a sharp stream of water that was hot, after soaking. Following a final rinse of cold water, the pads must be shaken and set on a level, non-rusting surface for drying. Pads will not be prepared for reuse till they are completely dry.
Hint: When pads become worn, they can be cut into small sections that can be properly used as foot or hand scratch pads.
Wet/Dry Vacs
Rinse out in, wipe in and outside after each use.
Rinse and wipe fasteners and hoses.
Carpeting Machines
Rinse out in of filters, tank, hoses and attachments.
Discharge pressure.
Wipe outside.